Log day 3 nutrient addition and airlock backflow

This commit is contained in:
Shard
2026-07-19 01:07:37 +00:00
parent e3d72fa6d1
commit e22a82c6eb
3 changed files with 61 additions and 1 deletions
+1
View File
@@ -26,6 +26,7 @@ A beginner-friendly project plan for making a **3 gallon apple-butter flavored m
6. Follow [`schedule.md`](schedule.md) for day-by-day reminders through aging/bottling.
7. Read [`apple-butter-flavor-plan.md`](apple-butter-flavor-plan.md) before post-fermentation flavoring.
8. Use [`bench-trial.md`](bench-trial.md) before adding apple concentrate, spices, extracts, acid, or tannin to the whole batch.
9. If the airlock pulls liquid into the bucket, see [`airlock-backflow.md`](airlock-backflow.md).
## Safety and quality rules
+59
View File
@@ -0,0 +1,59 @@
# Airlock Backflow Troubleshooting
Backflow means liquid from the airlock gets pulled into the fermenter. It can happen when pressure inside the bucket drops or when reseating the airlock pushes/pulls air and creates suction.
## Current batch incident log
- Day 2 temperature reported: 64.5°F.
- Repeated issue: about half the sanitizer liquid from the airlock backfed into the bucket while putting the airlock back into the bucket lid.
## How serious is it?
If the airlock liquid was properly diluted Star San or clean sanitizer solution, this is usually **not batch-ending**, especially in a 3 gallon batch. Star San is no-rinse at correct dilution and small amounts are commonly not a major problem.
If the airlock contained dirty water, old sanitizer, or anything questionable, risk is higher. Watch the batch, but do not panic.
## Why it happens
Common causes:
- Pushing the airlock into a tight grommet while the lid is sealed.
- Pulling/reseating the airlock changes pressure inside the bucket.
- Temperature drops cause contraction and suction.
- Bucket lid flexes and acts like a diaphragm.
- Airlock is overfilled.
## Prevent it next time
Preferred approach:
1. Do not push a filled airlock into a sealed lid.
2. Seat the dry/empty airlock body in the grommet first if possible.
3. Then fill the airlock to the line after it is installed.
4. Keep the airlock only filled to the marked line, not high.
5. When removing/reseating, crack the bucket lid edge slightly first to equalize pressure, then reseal.
6. Use a spray bottle of sanitizer on the grommet/airlock instead of dunking and installing it full.
## Safer alternatives
- Use cheap vodka in the airlock instead of sanitizer, if available.
- Use less airlock liquid, only to the fill line.
- Use a blowoff tube into a jar of sanitizer during active fermentation if the airlock keeps giving trouble.
## What not to do
- Do not repeatedly remove/reseat the airlock unless necessary.
- Do not overfill the airlock.
- Do not try to remove the sanitizer from the batch.
- Do not dump or restart the batch because of this alone.
## What to watch for
Over the next few days, watch for:
- normal fermentation activity continuing
- no fuzzy mold growth
- no rotten/putrid smell beyond normal fermentation sulfur/yeast notes
- gravity dropping on schedule when checked
If it smells aggressively bad, looks fuzzy/moldy, or fermentation stalls, ask Shard before intervening.
+1 -1
View File
@@ -20,7 +20,7 @@
|---|---:|---:|---:|---:|---|
| 2026-07-16 22:51 EDT | 0 | 1.100 | 74.5°F | | Brew day / pitch; 3 gal batch; logged honey as 9 lb raw honey |
| 2026-07-17 21:40 EDT | 1 | | | | Nutrient addition 1 complete: degassed, added 3 g Fermaid O mixed with clean water |
| | 2 | | | | Nutrient addition 2 |
| 2026-07-18 21:06 EDT | 2 | | 64.5°F | | Nutrient addition 2 complete; degassed/added Fermaid O. Airlock backflow issue repeated: about 1/2 sanitizer liquid sucked into bucket while reseating airlock in lid. |
| | 3 | | | | Nutrient addition 3 |
| | 5 | | | | Nutrient addition 4 or 1/3 break |