Files

3.6 KiB
Raw Permalink Blame History

Process Guide — First 3 Gallon Batch

Phase 0 — Before brew day

  • Buy all equipment and ingredients from shopping-list.md.
  • Read this whole process once.
  • Choose a fermentation spot around 62–68°F if using Lalvin 71B.
  • Clean equipment with PBW/OxiClean Free.
  • Sanitize equipment with Star San immediately before use.
  • Print or open logs/fermentation-log.md.

Phase 1 — Brew day

  1. Sanitize the fermenter, lid, airlock, spoon, funnel, hydrometer jar, and anything touching must.
  2. Add about 1 gallon of room-temperature spring/filtered water to the 6.5 gallon bucket.
  3. Add 9 lb honey. Warm the sealed honey containers in warm water if needed; do not boil the honey.
  4. Stir thoroughly until dissolved.
  5. Top up with water to 3 gallons total. The 6.5 gallon bucket will look underfilled; that is intentional for primary headspace.
  6. Mix well and take an original gravity reading. Record it.
  7. Make sure must temperature is in the yeast-friendly range, ideally mid-60s °F for 71B.
  8. Rehydrate yeast with Go-Ferm if using it; otherwise pitch yeast according to packet instructions.
  9. Add lid and airlock.
  10. Label the fermenter with date, recipe name, yeast, and OG.

Phase 2 — Early fermentation, days 1–7

  • Keep temperature stable.
  • For the first few days, gently degas/aerate once or twice daily if fermentation is active.
  • Add Fermaid O according to the staggered schedule in recipe.md.
  • Always degas before nutrient additions to avoid foam-over.
  • Record gravity readings if you take them.

Phase 3 — Primary completion

Primary is likely done when:

  • Airlock activity slows significantly, and
  • Gravity is stable across 2–3 readings several days apart.

Do not trust bubbles alone. Use the hydrometer.

Phase 4 — Rack to secondary

  1. Sanitize the 3 gallon carboy, bung, airlock, auto-siphon, and tubing.
  2. Siphon mead off the sediment into the 3 gallon carboy.
  3. Avoid splashing; oxygen is now the enemy.
  4. Attach airlock.
  5. Let it clear/age.

Phase 5 — Stabilize

When fermentation is done and gravity is stable:

  1. Add potassium metabisulfite/Campden at label dosage.
  2. Add potassium sorbate at label dosage.
  3. Wait at least 24 hours.

Phase 6 — Backsweeten and flavor

  1. Pull measured samples.
  2. Run bench trials using bench-trial.md.
  3. Choose the best sweetness/flavor dosage.
  4. Scale carefully to the full batch.
  5. Add vanilla beans/extract first; wait/taste.
  6. Add butter/butterscotch extracts only after stabilization and bench trials.
  7. Adjust acid/tannin/salt only if needed.

Phase 7 — Aging

  • Give it time. Young mead can taste hot, thin, or harsh.
  • Taste monthly.
  • Rack again if thick sediment accumulates.
  • Keep headspace low during aging.

Phase 8 — Bottling

Bottle only when:

  • Gravity is stable.
  • Mead is clear enough for your preference.
  • Flavor is where you want it.
  • You are not relying on fermentation to carbonate.

For still mead, use wine bottles/corks or beer bottles/caps. Store cool and dark.

Troubleshooting quick notes

Problem Likely cause First response
Rotten egg smell stressed yeast / nutrient issue Check temp, gently degas, confirm nutrient schedule
Fermentation stopped early temp, pH, nutrition, yeast alcohol limit Warm gently, check gravity/pH, ask before drastic fixes
Too sweet fermentation stalled or over-backsweetened Balance with acid/tannin; do not bottle if unstable
Too hot/alcoholic young mead Age longer
Butter flavor tastes fake too much extract Blend back with unflavored mead if possible